Oppo a9 2020 disassembly / teardown
Oppo A9 2020 (CPH-1941) Disassembly
Welcome, dear followers, to a new lesson on our website, advanced settings : OPPO A9 2020 Disassembly.
%20%20Disassembly.webp "oppo a9 2020 teardown") |
| oppo a9 2020 teardown |
Oppo A9 2020 (CPH1941) Teardown
Our topic today is about how to disassemble the Oppo A9 2020 and Oppo CPH 19 41 phone.The method of disassembling this phone is not like other similar phones. We must heat it on the back until the adhesive comes off. After that, we remove the cover from the back, and then we find the screws or nails.
How to disassemble Oppo A9 (2020)
After removing the screws, we also remove the SIM card holder, and then we disassemble the phone as shown in the video below.We advise use a specialized heating tool, such as a heating mat, heat gun, or separating machine. It will make the procedure simpler. You can use a hairdryer at home, but to gently heat and concentrate the heat flow in the desired area, you will need to construct a nozzle by hand or have one in the kit. To soften the glue below, heat must be applied to the rear cover's surface. 50° C, or 125° F, is the approximate heating temperature.
oppo a9 2020 teardown
To separate, use a pick or a tiny piece of plastic sheet. Use isopropyl alcohol to help the procedure along. The hardest part of dividing something is usually passing the tool between the halves. Select the nearest edge to the FFC buttons or cables.A video on how to disassemble the Oppo CPH 19 41 phone
The way to disassemble the Oppo A9 2020 phone is easy and simple. Dear viewers, all you have to do is follow the video from beginning to end.
In the end, you will learn a great way to disassemble the Oppo CPH 19 41 phone.
The disassembly method for all Oppo phones is easy and simple.
- Oppo a9 2020 complete disassembly
- Oppo A9 2020 (CPH-1941) Screen Replacement
- Oppo A9 2020 LCD replacement
- OPPO A9 2020 Disassembly
- How to disassemble your oppo a9
- oppo a9 2020
- oppo a9 2020 battery price
- Remember to switch off your phone before dismantling.
- Use the Paperclip or Ejector Tool (also known as Needle). Pull out the SIM and Micro SD card tray after inserting the tip all the way into the opening and causing the tray to eject.
- Be mindful! The instrument needs to be placed into a hole on the phone's housing's edge. Don't exert too much pressure. The tray eject mechanism might be broken by it.
- We advise use a specialized heating tool, such as a heating mat, heat gun, or separating machine. It will make the procedure simpler. A hairdryer from home can be used.
- To soften the glue below, heat must be applied to the rear cover's surface. 50° C, or 125° F, is the approximate heating temperature.
- To separate, use a pick or a tiny piece of plastic sheet. Use isopropyl alcohol to help the procedure along. The hardest part of dividing something is usually passing the tool between the halves. Select the nearest edge to the FFC buttons or cables.
- Avoid using any force to separate the components inside, such as a lever.
- With a Phillips 1.5 mm PH000 screwdriver, remove one screw to release the bracket that holds the fingerprint sensor connector.
- Remove the rear cover by prying apart the fingerprint sensor connector.
- Remove 15 screws using a Phillips 1.5 mm PH000 screwdriver.
- Take off the antenna-covered center cover covering the printed circuit board (PCB). To avoid unintentionally touching or short-circuiting anything on the PCB, try to lift the covers by their edges rather than pushing anything in between.
- As soon as you can, disconnect the battery connector.
- The BLP727, or rechargeable battery, has a 5000 mAh capacity and is compatible with the Oppo A9 2020 (CPH1941) model.
- Disconnecting the connector is highly advised in order to prevent any potential short circuits when disassembling the component.
- Remove four screws with a Phillips 1.5 mm PH000 screwdriver.
- Take out the antenna-equipped loudspeaker assembly.
